Wuxi Chaoqiang Weiye Technology SUP20S wiring mode

     Wuxi Chaoqiang Weiye Technology Co., Ltd. is a high-tech enterprise located in the machine Photoelectric Industrial Park of Hongshan street. It focuses on the R&D and production of laser equipment products, provides high-quality optical fiber laser welding hardware solutions, and has a number of patented technologies. Its products are widely used in cutting, welding and other fields to meet the needs of customers with enterprise products, Committed to building domestic independent brands. Our tenet: honest, innovative, pragmatic and dedicated people follow the principle of "customer demand is our goal, market occupation is our pursuit", work together with customers for win-win results, continuous development, create enterprise dreams, benefit employees and give back to the society.

一.Wiring composition

The welding gun is connected to the control box with three wires, including: two cores of the motor power cord, five cores of the motor signal cable, three cores of the safety lock and trigger button wire

The control box motor power/signal cable (two black) is directly connected to the motor part of the welding head and can be removed (two options are optional: 1. Open the motor cover and side panel of the handheld welding torch 2. Open the control box are plugs

A is used in the middle of the three-pin wire for the safe lock and trigger cord

二. size

三. The following are the control box wiring

Note: The ground wire of the switching power supply must be effectively grounded!.

Note: Clean the 5/6 pin of the system short-circuit signal interface one

2.1.1 Controller power supply terminal

The power supply uses the 5P interface, and the supplied 24V switching power supply and 15V switching power supply are used for power supply

Please note that the 15V switching power supply distinguishes the positive and negative poles, V1 is connected to 15V+, V2 is connected to 15V-, and any COM on the 15V switching power supply is connected to pin 2 GND!

Please note that the switching power supply must be grounded!

2.1.2 Controller LCD24/5000  

The LCD cable is delivered with the device and can be connected directly. See the figure above for specific definitions

2.1.3 Controller signal interface 1

①/②Pin is the air pressure alarm signal input, if you need to enable (wiring required), please set the air pressure alarm level in the background as high, otherwise it is low

The ③/④ pin is the water tank alarm signal input. If you need to enable it (wiring is required), please set the air pressure alarm level in the background as high, otherwise it is low

⑤The number pin is the reference ground for the safety ground lock, and it is directly connected to the processing workpiece with a wire

⑥ No. pin is the safety ground lock of the welding head, connected to the blue wire of the three-core wire, when the welding head touches the workpiece, the safety lock is on at this time

⑦The number pin is the switch of the welding head, connected to the brown wire of the three-core wire

⑧Pin No. is the light switch of the welding head, connected to the black wire of the three-core wire, when the trigger is pulled, the trigger button is on

Please note that only when there is no alarm, and the signal of the safe lock and trigger button is on, the output signal of the subsequent port will be sent out.

2.1.4 Controller signal interface 2

The 2 end of the signal interface uses a 6P interface, and the air valve is related to the wire feeding

①Reserved feet

②Reserved feet (synchronized with 4-pin signal)

③/④The foot is the valve 24V output, connect to the valve

⑤/⑥The pin is the signal wire of the wire feeder, the signal port of the wire feeder, regardless of positive or negative

2.1.5 Controller signal interface 3

①Pin is the laser alarm signal input +, if you need to enable it, please set the air pressure alarm level to high in the background

②Pin is enable+, connect to laser enable+

③The pin is 24V output, directly output 24V+ after power on

④Pet No. is a common ground (reference ground for feet 1/2/3/5)

⑤The number pin is analog quantity + output, the analog quantity is given

⑥Pin is PWM-modulated signal

⑦The number pin is PWM+ modulation signal